Видео

In most modern cars if you disconnect the battery like this without keeping power to the ECU it can cause you even more problems. Don't just disconnect the battery like this.

Does replacing the tumbler apply to the key not going into the off position- basically it turns on, and backwards but only goes as far as the auxiliary position and it’s killing my battery constantly auto is 2012 Mazda CX9

Is it the same on a 2007 Yaris ?

Great job wearing gloves and not touching the halogen bulb.

Im gona go to the car right meow and see if this can be done thanks man will give update

Thanks

Thanks for the great view. Only thing that would make it better is to show how the screwdriver can come down from above to turn it.

No tools your using a ratchet u plonka

114 on ebay now

still enigne light on dam

Now what to do if my new replacement parts only have one adjuster and the old ones had two?

Thank you!!!

Says no special tools,he's hardly using a special tool😂

Thats not the dash dude

good video...yes... but as we all know different car comes with different types of socket adjustment...

Walmart car batteries are 💩

THANK YOU FOR KEEPING IT SIMPLE.

get a OBD2 reader they're cheap enough

It works thanks!❤

Finally someone explain how to turn that screw to which direction for making the beam lower or higher. Those clockwise and counterclockwise from other videos were so confusing. Thank you very much.

Great video. The plastic covers also got hazy and yellow, but I had to replace my headlights because one of the halogen bulbs fell out of the socket. Part of the socket holding the bulb melted and it then landed on the windshield wiper reservoir, leaving a massive hole in the reservoir.

It’s normal tools

He said no special tools

I just need a smog check! I’m going to try to do this myself. Thank you

Entire vid shows one shot that could have been put in a blog. Worthless.

This was perfect!! Exactly the information I needed. Thank you!!

How to active bluetooth pin?

Thank you for posting this!

I know this video and thread is as old as the hills but I’ve just found a bottle of this stuff. One thing everyone must remember is: There are three layers to car paint, a base coat, a colour coat and a clear coat. If your scratches go through the clear and the paint coats, you must replace with colour paint, there’s no magic fix. But if you’ve only gone through your clear coat, you maybe able to polish away those scratches by removing clear coat paint. 👍

Perfect Instructions!! Bravo, subscribed!

Super helpful. Straight to the point. Thank you!

That CRC forms a latex film, it only goes on the back of the pad. You have to use brake grease or anti-seize between the pad and the clips. Also, you have to take out the guide pins and put silicone grease on them. This is not how you do a brake job. 🤦‍♂🤦‍♂🤦‍♂

Thank you for a helpful video, you just got right to the point and answered the question! Clearly explained great job

It amazes me how people have fancy cameras, all the time and knowledge to make videos, all the equipment. But they still puzzle with 1 hand 😂😂to

Thanks!

You'll need to use an adhesion promoter to get it to stick properly. 3M make one. That's what the factory use, also good body work shops.

What about the 3 against the firewall

Walmart batteries are not standardized,the top post are not up front, instead they are in the back.

I bought some today, i w8ll se how it does on my trip to Nashville.

The context and general advice that you provide (of this particular job) acts as a very helpful prologue before getting into one of the other step-by-step videos. I love it and hope you keep dropping more videos like these. The autoparts link that you provide takes me to the auto-part main page on Amazon but it would be quite useful if there was a specific parts link that listed the gaskets needed. Even though you recommend calling the dealerships, sometimes it helps provide more context of what I''m asking for when I can see the parts before hand. Cheers!

Thanks a lot man I appreciate it. You saved my time

Very helpful still 10 years later thank you brother

Does anyone know how to repair RPM gauge illumination? None of the lights in RPM gauge not working including check engine, mileage etc. This is 2006 Mini. Thank you in advance

Very helpful, thanks!

I love you. I've had multiple life experiences. Flying jets etc. You saved my life.

Nice video and straight to the point. But what you failed to mention is what kind of vehicle this is on? Different vehicles have different headlight adjustors on it. My doesn't have this...

My mini is a 2004 Mini Cooper regular you know and it has a DSC switch and I can't find out what that is for

My power cords have an extra white with green not shown here. Idk what to do with it

Bulsheet

Is there a way to replace the lenses instead of the whole fixture?